番村站地铁深基坑支护结构设计毕业论文

 2021-04-14 11:04

摘 要

此次毕业设计是以广东佛山地铁番村站深基坑为工程背景,开展该基坑的支护结构设计工作。具体的设计流程是:首先,根据工程资料及地质勘察报告,初步确定围护方案为钻孔灌注桩加止水帷幕及坑内设置3道内支撑。根据土层条件和基坑形状确定了三个计算截面,分别为1-1截面、2-2截面、3-3截面。设计时采用的计算方法为:土压力部分为朗肯土压力理论及水土合算;围护结构内力上是用逐层开挖支撑支承力不变法求内支撑轴力,用对净土压力零点求力矩平衡的方式求围护桩上的弯矩。完成初步设计后,根据相关规范的要求完成了各种稳定性验算;并通过plaxis2D数值分析软件进行模拟,检验了支护方案的合理性。在完成内支撑及围护结构的计算后,按照规范要求确定了基坑监测方案。最后,完成了计算书的撰写和相应施工图的绘制。

关键词:深基坑;钻孔灌注桩;内支撑;施工监测

Design of Supporting Structure for deep excavation of Pancun Subway Station

ABSTRACT

This graduation project is based on the deep foundation pit of Fancun Station of Foshan Metro, Guangdong Province, to carry out the support structure design of the foundation pit.The concrete design process is as follows: Firstly, according to the engineering data and geological survey report, the preliminary determination of the enclosure scheme is that the bored cast-in-place pile is added with water-proof curtain and three inner supports are set up in the pit. According to the soil condition and the shape of foundation pit, three calculation sections are determined, which are 1-1 section, 2-2 section and 3-3 section. The calculation method used in the design is: Rankine earth pressure theory and water and soil cost-effective; the internal force of the retaining structure is calculated by the method of invariant supporting force of excavation layer by layer, and the bending moment of the retaining pile is calculated by balancing the moment of the zero point of net earth pressure. After the preliminary design is completed, various stability checks are completed according to the requirements of relevant specifications, and the rationality of the support scheme is verified by simulation with PLAXIS 2D numerical analysis software. After the calculation of internal support and enclosure structure is completed, the monitoring scheme of foundation pit is determined according to the requirements of the code. Finally, the compilation of the calculation book and the drawing of the corresponding construction drawings are completed.

Key words:deep excavation;Bored Pile; Internal Support; Construction Monitoring

目 录

1 设计方案综合说明 1

1.1 工程概况 1

1.2 工程地质与水文地质 1

1.2.1 地形地貌 1

1.2.2 岩土分层及其特性 2

1.2.3 水文地质条件 3

1.3 设计内容 3

2 支护方案的选择及比较 4

2.1 基坑支护方式的选择 4

2.1.1 钻孔灌注桩 4

2.1.2 地下连续墙 4

2.2 方案的比较及确定 4

2.2.1 基坑的特点 4

2.2.2 支护方案的选择 4

2.3 计算截面的选择 5

2.4 计算方法 6

3 1-1截面围护结构设计 8

3.1 1-1截面的土层计算参数 8

3.2 1-1截面的土压力计算 8

3.2.1 1-1截面的主动土压力计算 9

3.2.2 1-1截面的被动土压力计算 10

3.2.3 1-1截面的净土压力计算 11

3.2.4 1-1截面的土压力合力及作用点的位置 11

3.3 1-1截面处内支撑轴力计算 12

3.3.1 第一道支撑轴力计算 13

3.3.2 第二道支撑轴力计算 14

3.3.3 第三道支撑轴力计算 14

3.4 1-1截面处围护结构上最大弯矩计算 15

3.4.1 第一道支撑附近 16

3.4.2 第二道支撑附近 16

3.5 嵌固深度计算 17

3.6 稳定性验算 17

3.6.1 1-1截面模型的建立及电算 18

3.6.2 1-1截面处整体稳定性验算 19

3.6.3 1-1截面处基坑的抗隆起稳定验算 19

3.6.4 1-1截面处基坑的抗渗流稳定性验算 21

3.6.5 1-1截面处基坑支护结构踢脚稳定性验算 22

3.7 本章小结 24

4 2-2截面围护结构设计 25

4.1 2-2截面的土层计算参数 25

4.2 2-2截面的土压力计算 25

4.2.1 2-2截面的主动土压力计算 26

4.2.2 2-2截面的被动土压力 27

4.2.3 2-2截面的净土压力 28

4.2.4 2-2截面的土压力合力及作用点的位置 28

4.3 2-2截面处内支撑轴力计算 29

4.3.1 第一道支撑轴力计算 30

4.3.2 第二道支撑轴力计算 31

4.3.3 第三道支撑轴力计算 31

4.4 2-2截面处围护结构上的最大弯矩计算 32

4.4.1 第一道支撑附近 33

4.4.2 第二道支撑附近 33

4.4.3 第三道支撑附近 34

4.5 嵌固深度计算 34

4.6 稳定性验算 35

4.6.1 2-2截面模型的建立及电算 35

4.6.2 2-2截面处整体稳定性验算 36

4.6.3 2-2截面处基坑的抗隆起稳定验算 36

4.6.4 基坑的抗渗流稳定性验算 38

4.6.5 基坑支护结构踢脚稳定性验算 39

4.7 本章小结 40

5 3-3截面围护结构设计 42

5.1 3-3截面的土层计算参数 42

5.2 3-3截面的土压力计算 42

5.2.1 3-3截面的主动土压力 43

5.2.2 3-3截面的被动土压力 44

5.2.3 3-3截面的净土压力 45

5.2.4 3-3截面的土压力合力及作用点的位置 45

5.3 3-3截面处内支撑轴力计算 46

5.3.1 第一道支撑轴力计算 47

5.3.2 第二道支撑轴力计算 48

5.3.3 第三道支撑轴力计算 48

5.4 最大弯矩计算 49

5.4.1 第二道支撑附近 50

5.5 嵌固深度计算 50

5.6 3-3截面处基坑的稳定性验算 51

5.6.1 3-3截面的模型建立及电算 51

5.6.2 3-3截面处整体稳定性验算 52

5.6.3 3-3截面处基坑的抗隆起稳定验算 52

5.6.4 3-3截面处基坑的抗渗流稳定性验算 53

5.6.5 3-3截面处基坑支护结构踢脚稳定性验算 54

5.7 本章小结 56

6 围护结构的配筋 57

6.1 1-1截面处的围护桩的配筋计算 57

6.2 2-2截面处的围护桩的配筋计算 58

6.3 3-3截面处的围护桩的配筋计算 59

6.4 本章小结 60

7 内支撑设计 62

7.1 1-1截面处内支撑的设计及计算 62

7.1.1 第一道支撑设计 62

7.1.2 第二道支撑设计 63

7.1.3 第三道支撑设计 64

7.2 2-2截面处内支撑的设计及计算 66

7.2.1 第一道支撑设计 66

7.2.2 第二道支撑设计 67

7.2.3 第三道支撑设计 69

7.3 3-3截面处内支撑的设计及计算 69

7.3.1 第一道支撑设计 69

7.3.2 第二道支撑设计 71

7.3.3 第三道支撑设计 72

7.4 本章小结 73

8 围檩设计 74

8.1 围檩的设计及计算 74

8.2 本章小结 75

您需要先支付 80元 才能查看全部内容!立即支付

课题毕业论文、开题报告、任务书、外文翻译、程序设计、图纸设计等资料可联系客服协助查找,优先添加企业微信。